It involves a lot of taping, sanding, and mudding before you can finally declare that the work has been done. And we haven't even mentioned the dusty mess it makes. It's a time-consuming process and what is worse is that it's not a one-time experience. After pouring in days of labor on installing drywall, it still needs to be maintained carefully.
Drywall is fairly prone to damage and is not guaranteed to last you a long time. When drywall starts getting damaged, it happens visibly. A child with a marker can ruin an entire room in seconds flat. So why do people insist on using drywall? Are there no other options for home improvement?
Turns out there are! The following are some of the best drywall alternatives available on the market. All I think about with drywall is children and pets ruining it, an unruly teenager punching a hole through it, and how no amount of precision spackling can actually repair the damage. It will always be visible. It can warp over time, bloat from moisture, and honestly looks cheap once you've seen the alternatives. Let's look at those now. Wood planks are an age-old drywall alternative that has certainly stood the test of time well.
These wood planks allow you to give your home an elegant and rustic feel without the maintenance issues that come with traditional drywall. Once the plank has been hung you don't need to do anything to maintain them apart from keeping them dry, especially if you seal them with a light lacquer finish so you can wipe even marker off easily. This is a cost-effective alternative and is especially suited to country-style homes. You can also choose from different types of wood and finishes, thus giving you a lot of variety.
Wood planks, however, do not go with all kinds of homes. If you are building a modern home then, perhaps, wood plank walls won't be the best fit unless you only cover the bottom half and install protective chair rails.
But this look went out of style in the 's, to be honest, especially combining it with wallpaper. By covering the entire wall, floor-to-ceiling, you can pull off a cabin aesthetic easily though.
Veneer plaster might be the alternative that comes closest to traditional drywall. However, veneer plaster is simpler to use than drywall. It doesn't require as many skills or tools as hanging drywall does. If ease-of-use matters to you, give this some consideration. However, it is also the most laborious and time-consuming alternative on this list.
While handling veneer plaster is not necessarily difficult, it can take up practically the whole day to get the job done. This type of wall is constructed where tensile force is acted. The reinforcement is required in horizontal and vertical. Horizontal reinforcement is provided in every third or fourth course. Sometimes hoop iron reinforcement is provided. This wall is constructed into two parts inner and outer, with a c avity of mm.
The thicker wall is inside the room, and the thinner one is outside of the building. A thick wall carries all the load of the slab , and the outer wall resists external moisture and other effects.
Load-bearing walls are the types of walls that carry the roof slab load and upper loads of floors. There are mainly six types of Load-bearing walls, they are-. This type of wall is used for its durability and huge strength. This type of wall is easy to install it provides huge safety.
Some characteristics of this type of wall are-. Retaining walls are relatively rigid walls used for supporting soil laterall y so that it can be retained at different levels on the two sides. Retaining walls are structures designed to restrain soil to a slope that it would not naturally keep to typically a steep, near-vertical or vertical slope.
The Retaining wall is constructed to retain the lateral pressure of soil and holds the materials. Retaining wall provides support thus, it is also called a breast wall or resentment wall. Masonry wall has great architectural beauty, and it provides the required strength. Masonry is the word utilized for development with mortar as a coupling material with singular units of blocks , stones, marbles, rocks, solid squares, tiles, and so forth.
Mortar is a blend of restricting material with sand. It is used for building exterior wall cladding. The metal can be stainless steel , copper, aluminium. It supports gravity, seismic and wind loading. This type of wall is mainly used in the exterior wall and is made of aluminium, steel, copper, etc. Traditionally, Engineering bricks are used where in construction where strength and resistance to water and frost attack are important.
Some common application examples are retaining walls , damp proof courses, manholes, sewers and general ground works. This types of brick are more useful from a practical point of view. It has good architectural beauty as it has a good external finish. This Is extremely good for frost attack. Stretcher bond is one of the most common bonds. It is easy to lay with little waste and composed of stretchers set in rows, offset by half a brick. A pattern made up of rows of stretchers with each stretcher centred on the stretcher below it.
All joints run vertically down the wall. In this type of bond, all bricks are arranged in a stretcher course. This type of wall is constructed as a partition wall. In this type, all bricks are arranged in the header arrangement. Other options are under the sink were plumbing lines come through. Utility rooms are another good place to look. And finally, you can try checking under the insulation in the attic.
Drywall is attached to the studs only and the back side will often be a brown paper. In both cases, the wall may be covered with a wall surface So, how can you tell what it is? Well, start by looking at it. Then knock on it. Sheet rocked walls sound more hollow than plastered walls the plaster is stiffer and typically thicker. Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams?
Learn more. How to determine the type of wall on which I'm putting up a shelf? Ask Question. Asked 9 years, 4 months ago. Active 2 years, 7 months ago. Viewed k times. Improve this question. Rinzwind Rinzwind 1 1 gold badge 4 4 silver badges 3 3 bronze badges. In this article, we'll explore the composition, advantages and disadvantages of plaster and drywall for interior wall applications. The most common form of plaster for interior walls is gypsum plaster.
Plaster walls are generally created through a three-coat process. To begin, lath must be secured to the framing. Historically, lath has been made of wood strips, but more recently metal or plasterboard have come into use. The lath gives the gooey plaster something to hold onto.
After the lath is in place, the plaster compound must be mixed. The compound usually comes dry and must be mixed with water. While this step may sound fairly easy, a certain amount of skill and experience is needed to get the right consistency [source: Nash ]. Then, the plaster can finally be applied to the wall.
The first coat of plaster is applied, scratched and left to dry. It is followed by the second coat, or brown coat, and then the wall is finished off with a final layer.
Due to the number of coats and lathing, a plaster wall tends to be thicker than a drywall wall, which can create a greater air barrier [source: Heberle and Scutella ]. This thickness also creates a good sound barrier between rooms. If the lathing and framing are done well, plaster can provide a much more rigid wall leading to reduced likelihood of buckling or breaking. Since plaster is not a solid when it's applied to the wall, it can be a good choice for curved or irregular surfaces. Finally, the gypsum within the plaster has a high water content, which gives the walls fire -resistant qualities.
Even with these benefits, plaster has fallen out of favor with homeowners today. Let's look at some possibilities for why that might have happened.
First, the plastering process is labor intensive, causing the price to rise. Plastering is also time-consuming -- in applying and drying time. In addition, while plaster is very durable, it can crack with the settling of the building or improper installation. Some of these cracks can be fixed with plaster or a setting-type compound, yet others require structural restoration. These may be some of the reasons that homeowners and remodelers are now more likely to opt for the drywall.
Let's take a closer look at this interior wall material. While the three-coat authentic plaster process is rarely used in new homes today, veneer plaster is a similar alternative.
It offers the look of plaster and many of its beneficial traits, but takes much less time to apply. A veneer plaster starts with a blue board base, or gypsum board with special moisture and adhesive qualities [source: Pedracine ]. Then, either one or two coats of plaster are applied on top of the blue board in a similar manner to regular plastering.
0コメント